root@DD-WRT:~# gpio enable 5 #(SECURITY LED - will give you amber) root@DD-WRT:~# gpio disable 5 #(SECURITY LED - will give you amber bright) WARNING: "gpio disable 6" will completely erase your NVRAM (i.e. do a complete reset on your router) Linksys WRT610N v2.0 . It should also work for the v1.0.
hi i recently upgrade my WRT3200ACM to dd-wrt and the two leds indicators for wifi 2.4 and 5ghz are off, i have radio on and wifi active. thats So, having DD-WRT v24-sp2 running on my wonderful D-Link DIR-320 I have configured the Radio Time Restriction in such way it' starting daily at 18:00 (when normally I should be back from work) and runs until 24:00 (when I should be asleep). Posted: Sat Jun 07, 2008 13:29 Post subject: Can't turn off wireless on WRT54GL v1.1: Hi all, I'm using WRT54GL v1.1 with DD-WRT v24 std, dated 2008-05-24. By default the radio is turned on at startup. For two days I've been unable to turn off the wireless signal using the EZ-Setup button. Oct 28, 2007 · Turn off wlan: stopservice nas wl -i eth1 radio off. Turn on wlan: stopservice nas wl -i eth1 radio on startservice nas. This Code was tested by my DD-WRT, it's work fine! (Last edited by AppleWolf on 25 Feb 2009, 18:01) Available Settings: Off, Static Default Setting: Off Recommended Setting: Off* The purpose of Spatial Multiplex Power Save (SM power save) is to allow a MIMO 802.11 device to power down all but one of its radios. For example, a 4×4 MIMO device with four radio chains would power down three of the four radios, thus conserving power. I have the Netgear WNR3500L v2 on DD-WRT build v3.0-r43502 giga … 12:32 PM Ticket #6807 (Special Characters Breaking DHCP Server r41027) closed From DD-WRT Wiki. Jump to: navigation You can turn on/off the wireless transmit of your router by pressing this button. ** You must have "Use this button for
Posted: Sat Jun 07, 2008 13:29 Post subject: Can't turn off wireless on WRT54GL v1.1: Hi all, I'm using WRT54GL v1.1 with DD-WRT v24 std, dated 2008-05-24. By default the radio is turned on at startup. For two days I've been unable to turn off the wireless signal using the EZ-Setup button.
Available Settings: Off, Static Default Setting: Off Recommended Setting: Off* The purpose of Spatial Multiplex Power Save (SM power save) is to allow a MIMO 802.11 device to power down all but one of its radios. For example, a 4×4 MIMO device with four radio chains would power down three of the four radios, thus conserving power.
Nov 06, 2009 · Posted: Sat May 30, 2009 20:09 Post subject: WRT54G v8 radio off after cold boot: My WRT54G v8 (yeah, I know its crappy) works fine thanks to dd-wrt. The problem is, when it cold boots (for example when you plug AC out and in again) the radio never works. I get TX errors (22 errors) and then the radio seem to give up.
Arg 1 is the country abbreviation Arg 2 is the band(a or b) (editors note: only b seems to be recognized in dd-wrt v22) Example: wl channels_in_country JP b curpower. Return current tx power settings evm. Start an EVM test on the given channel, or stop EVM test. Arg 1 is channel number 1-14, or "off" or 0 to stop the test. Posted: Thu Feb 02, 2012 7:08 Post subject: Loaded dd-wrt and radio is OFF or not showing: Hi all, I loaded dd-wrt on my Dlink DIR825 and with super channel enabled. It seems dd-wrt couldn't find the Radio. When I loaded factory image, radio would show up and worked fine, but when I loaded dd-wrt, in wirelesss->basic settings, radio will show hi i recently upgrade my WRT3200ACM to dd-wrt and the two leds indicators for wifi 2.4 and 5ghz are off, i have radio on and wifi active. thats So, having DD-WRT v24-sp2 running on my wonderful D-Link DIR-320 I have configured the Radio Time Restriction in such way it' starting daily at 18:00 (when normally I should be back from work) and runs until 24:00 (when I should be asleep).